Save

46%

On RRP

Megger MFT1741 PLUS Multifunction Tester EVCA210-UK EV EVSE KIT

£1,245.00 Inc VAT: £1,494.00

    2 in stock

    Calibration Certificate

    Add a 12 month Calibration Certificate

    Description

    Megger MFT1741+ Multifunction Tester EVCA210-UK EV EVSE KIT

    The Megger MFT1741 PLUS Multifunction Tester EVCA210-UK EV EVSE KIT can be used to troubleshoot and verify the functionality and safety of industrial, commercial and domestic fixed wiring installations, as well as electric vehicle charging points. It is particularly well suited to testing low voltage electrical installations in areas with high electrical noise.

    The Megger EVCA210-UK Electric Vehicle Charge-Point Adapter, coupled with the MFT1741+ can be used to verify the functionality and safety of single- and three-phase electric vehicle charge points in accordance with IEC/ EN 61851-1 and IEC/ HD 60364-7-722.

    Test instruments, such as the aforementioned single and multifunction testers, can be front-mounted to the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter’s mains socket or via the 4mm connection ports, L1, L2, L3, N and PE. Additionally, the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter includes CP signal terminals via which an oscilloscope can be connected, thereby allowing the user to measure CP signals.

    Compact and simple-to-use, the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter is designed to provide all the functions required to fully test Mode 3 AC electric vehicle charge points and is compliant with UK, European and other international wiring regulations and standards, such as the Low Voltage Directive LVD 2014/35. To this end, the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter is supplied with a type 2 connector for testing charging points with panel-mounted sockets or a fixed cable with a vehicle connector, and a type 1 connector for checking charging points with a fixed type 1 cable connector, such as those found on a Mitsubishi PHEV.

    The Megger EVCA210-UK Electric Vehicle Charge-Point Adapter simulates the connection of an electric vehicle to the charging point. The user triggers the simulated charging process by using the rotary switch to select either the Proximity Pilot (PP) or Control Pilot (CP) states.

    In addition to this, the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter features two dedicated function buttons for simulating either a CP Error “E” or PE Error (Earth Fault). The CP Error simulates an error on the control pilot circuit while the PE Error simulates the disconnection of the PE circuit; both of these manual tests can be used to ensure the output of the charge point is disconnected correctly.

    Importantly the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter also includes a function button for performing a manual PE Pre-Test which checks whether any dangerous voltages are present on the PE circuit. This test should be performed prior to commencing any other checks; if the EV charging point fails the PE Pre-Test all other tests must be halted until after the fault has been investigated and rectified.

    Finally, the Megger EVCA210-UK Electric Vehicle Charge-Point Adapter has an ingress protection rating of IP54 and a safety rating of CAT II 300V.

    The Megger EVCA210-UK Electric Vehicle Charge-Point Adapter is an ergonomic and easy-to-use adapter specifically designed for testing the safety and effectiveness of electric vehicle charging points.

    • Troubleshoot and verify the functionality and safety of industrial, commercial and domestic fixed wiring installations
    • Check EV charge points using the Megger EVCA210-UK (see below)
    • Ideal for testing low voltage electrical installations in areas with high electrical noise
    • Includes all the tests required to complete the relevant electrical certification
    • Please see the table above for an overview of the MFT1741 ’s testing capabilities
    • Visual and audible hazardous voltage indicators
    • Stops testing if a hazardous voltage is detected during insulation and continuity tests
    • NEW non-trip loop impedance technology
    • NEW confidence meter
    • NEW auto sequence for EV charge point RCDs
    • Large, clear, backlit, dual-readout display
    • Readings and test parameters are displayed in parallel
    • Digital/ analogue arc for indicating fluctuating readings
    • Colour-coded function controls
    • Function controls reduce the possibility of selecting the incorrect function or range
    • Does NOT include hidden or complicated measurement menus
    • Ambidextrous design: TEST and LOCK functions on either side
    • Automatic test start supports hands-free operation
    • Supplied with a neck strap
    • Stands independently
    • IP54
    • Powered by internal rechargeable batteries
    • Approximate battery life: four hours
    • Easy-to-use and ergonomic test instrument with an eclectic array of test functions
    • Megger MFT1741 Multifunction Tester
    • Printed Quick Start Guide for MFT1741
    • Full User Guide (CD) for MFT1741
    • Calibration Certificate for MFT1741
    • Megger SP5 Switched Probe
    • Megger Neck Strap
    • 3-Wire Lead Set with Prods and Clips
    • Mains Plug Test Lead (BS 1363)
    • AC Battery Charger
    • Large Soft Pouch with Extra Storage for MFT1741
    • Megger EVCA210-UK Electric Vehicle Charge-Point Adapter
    • Type 1 Charging Plug
    • Type 2 Charging Plug
    • Soft Carry Case for EVCA210-UK
    • Instruction Manual for EVCA210-UK

    MFT 1741+ Datasheet

    EVCA-210-UK Datasheet