Fluke 726 Precision Multifunction Process Calibrator

£4,206.00 Inc VAT: £5,047.20

    Available on back-order

    Calibration Certificate

    Add a 12 Month Calibration Certificate

    Description

    Fluke 726 Precision Multifunction Process Calibrator

    The Fluke 726 Precision Multifunction Process Calibrator is a precise, handheld calibration device designed to deliver accurate, detailed calibration procedures within the process industry.

    It is a multifunctional calibrator and can be used to measure and source voltage, mA, mV (TC terminals), resistance, frequency, loop supply, thermocouples (J, K, T, E, L, N, U, C, BP, XK, B, R and S) and multiple types of RTD. All of these functions are built into the same unit, negating the need to use additional devices during calibration procedures. It can also be used to measure and source pressure via the use of a (sold separately) Fluke 700 series Pressure Module.

    This calibrator features two separate channels for measuring and sourcing/viewing process signals simultaneously, carries out measurements with precise accuracies of just 0.01% and includes a large selection of additional functions such as HART mode, custom RTD curves, the ability to test transmitters and much more.

    It also includes limited memory functions and can store up to 8 calibration results and can store pre-set calibration procedures for ease of use in repeat testing.

    Measurement Accuracy
    Voltage DC
    30.000 V  0.01% 2 mV (upper display)
    20.000 V  0.01% 2 mV (lower display)
    90.00 mV  0.01% 10μV
    -10.00 mV to 75.00 mV  0.025 % 1 count (via TC connector)
    Current DC
    24.000 mA  0.01% 2 mA
    Resistance
    0.0 to 4000.0 Ω   /- 0.015%
    Frequency
    2.0 to 1000.0 CPM  0.05 % 0.1 cpm
    1.0 to 1000.0 Hz  0.05 % 0.1 Hz
    1.00 to 15.00 kHz  0.05 % 0.01 kHz
    Sensitivity  1 V peak-to-peak-minimum
    Pressure
    Accuracy  from 0.025% of range using any of 29 pressure modules.
     (for detailed specifications refer to pressure modules in options and accessories)
     Modules available for differential, gauge, vacuum, absolute, dual and high pressure.
    Source Accuracy
    Voltage DC
    100.00 mV  0.01% 10 μV
    20.000 V  0.01% 2 mV
    -10.00 mV to 75.00 mV  0.025 % 1 count (via TC connector)
    Current DC
    24.000 mA (Source)  0.01% 2 μA
    24.000 mA (Simulate)  0.01% 2 μA
    Resistance
    Range, Accuracy (Percent of reading floor) and Excitation Current  5 to 400 Ω, 0.015% 0.1 Ω, 0.1 to 0.5mA
     5 to 400 Ω, 0.015% 0.05 Ω, 0.5 to 3mA
     400 to 1500 Ω, 0.015% 0.5 Ω, 0.05 to 0.8 mA
     1500 to 4000 Ω, 0.015% 0.5 Ω, 0.05 to 0.4 mA
    Frequency
    2.0 to 1000.0 CPM  0.05%
    1.0 to 1000.0 Hz  0.05%
    1.0 to 10.0 kHz  0.25%
    10.0 to 15.0 kHz  0.5%
    Waveform:  5 V p-p squarewave, -0.1 V offset
    RTDs and Thermocouples
    Measure and Source Accuracy:
    Cu10  1.8 °C
    NI-120  0.15 °C
    PT-100 (385)  0.45 °C
    PT-100 (392)  0.35 °C
    PT-100 (391-JIS)  0.35 °C
    PT-200 (385)  0.95 °C
    PT-500 (385)  0.55 °C
    PT-1000 (385)  0.35 °C
    RTD Resolution:  0.01 C (0.01 F)
    Cu10.01 C  0.1 C (0.1 F)
    J:  0.4 °C
    K:  0.5 °C
    T:  0.4 °C
    E:  0.4 °C
    R:  1.4 °C
    S:  1.4 °C
    B:  1.4 °C
    L:  0.45 °C
    U:  0.45 °C
    N:  0.6 °C
    XK:  0.4 °C
    BP:  1.1 °C
    TC Resolution  J, K, T, E, L, N, U: 0.1 °C, 0.1 °F B, R, S: 1 °C, 1 °F
    Specifications
    Ramp Functions
    Source functions:  Voltage, current, resistance, frequency, temperature
    Ramps  Slow ramp, Fast ramp, 25% step-ramp
    Loop Power Function
    Voltage:  24 V
    Accuracy:  10%
    Maximum current:  22 mA, short circuit protected
    Step Functions
    Source functions:  Voltage, current, resistance, frequency, temperature
    Steps  25% of range, 100% of range
    Environmental Specifications
    Operating Temperature
     -10 °C to 55 °C
    Storage Temperature
     -20 °C to 71 °C
    Operating Altitude
     3000 m
    Safety Specifications
    Agency Approvals
     EN 61010-1:1993, ANSI/ISA S82.01-1994; CAN/CSA C22.2 No 1010.1:1992
    Mechanical & General Specifications
    Size
     200mm x 96mm x 47mm (7.9 in x 3.8 in x 1.9 in)
    Weight
     650 g (23 oz.)
    Batteries
     4 AA alkaline batteries
    Battery Replacement
     Separate battery compartment, accessible without breaking calibration seall
    Side port connections
     Pressure module connector, also used for remote real-time programming
    • Handheld and portable – ideal for use out in the field
    • Precise measurements with general accuracy of 0.01%
    • Transmitter error% calculation
    • Memory stores up to 8 calibration records
    • Frequency totaliser and frequency pulse train source mode
    • HART mode inserts 250 ohm resistor in mA measure and source for compatibility with HART instruments
    • Integrated pressure switch
    • Custom RTD curves
    • Voltage input protection
    • Two separate channels; measure, source and view process signals simultaneously
    • Measure, source and simulate volts, mA, RTDs, thermocouples, frequency and resistance
    • Measure or source pressure using Fluke optional pressure modules
    • Fast linearity testing with auto step and auto ramp functions
    • Power transmitters during test using 24V loop supply and simultaneous mA measurements
    • Fluke 726 Precision Multifunction Process Calibrator
    • TL75 Test Leads
    • AC72 Test Clips
    • One Pair of Stackable Test Leads
    • Product Overview Manual (Print)
    • CD-ROM Manual